Intuition Liners Home Fitting Instructions

 

IMPORTANT:

Before molding, try both liners on in your boots with any foot beds/orthotics you intend to use, to ensure they fit your boots and feet properly. Not too tight, not too sloppy!

**DO NOT MOLD IF THE LINERS DON’T FIT!**

You will need: Intuition Fit Kit (1 pair of stockings & 1 rubber toe cap)

microwave

short or long grain uncooked rice (do not use instant rice)

3lbs for sizes up to US Men’s 9 (4 lbs for higher sizes)

1. Fill one fitting sock with 3-4 lbs of long or short grain white rice and tie a knot at the end.

2. On a flat surface, spread rice throughout stocking to form a long sausage shape.

3. Keeping rice stocking in an even, tubular shape, place into microwave.

4. Based on wattage in manual or back panel of microwave, heat rice stocking for appropriate time: 700-900W=7min, 1000-1100W=5min, 1200-1250W=4min.

5. While rice stocking is heating, place toecap on first foot to fit.

(Intuition logo over big toe)

6. Place other fitting sock over toecap to secure. Pull stocking up evenly, eliminating all wrinkles.

7. CAUTION HOT! When timer goes off, by knotted end, pull rice stocking out of microwave.

8. Continuing to hold by knot, place rice stocking inside first liner (in boot). Work stocking into toe box and heel by tapping boot hard on floor multiple times, first on heel and then toe. Keep on tapping, going back and forth between heel and toe until rice stocking has settled deeper into liner.

9. Let boot stand with rice stocking inside for 4-12 min depending on liner model (refer to heating time chart). Remove heated rice stocking from liner. Insert foot bed now, if used. With toecap on securely, place foot into heated liner. When boot is on, kick heel of boot into floor to ensure heel and liner are in heel pocket firmly. Buckle or lace up to normal tension settings. Keep weight on boot 5-7 min STANDING with knees slightly bent. Keep heels down to avoid creating extra space resulting in heel lift. (You can also place your boots against a board (2x4) to help push heel back towards heel of boot).

10. Take off boot, stocking and toecap, and repeat for other liner.

ADDITIONAL FITTING TIPS

- Check fit before heating liners. Put liners in boots, with foot beds if you plan to use them. If toes are touching the end, that’s fine, the toecap will create extra space for you during molding. If they are curled up or jammed into the end of the liners then they are too small and you may need a larger size. Ideally, the liner should feel snug all over, with no uncomfortable pressure points. Feeling a bit too tight is okay because the liner will compress when heated and buckled down.

- We do not recommend heat molding a liner that feels loose. Do not rely on liner to expand to fill voids or sloppiness, instead consider choosing a thicker liner.

- If liners felt tight when you first tried them on, buckle extra tight when molding to compress foam and thin it out.

- If liners felt just right, buckle loosely so liner is held firmly but not compressed. This allows you to retain maximum thickness.

- After initial molding, if you need to adjust fit in a specific area (ex. ankle or toe box) consider making a smaller rice bag to use rather than re-molding entire liner.

- Cuff can be reheated and adjusted by shaping rice bag into a more condensed ball shape. Lay boot on side to allow rice bag to rest in top of cuff area.

- When heating an overlap style liner, you will want to position rice bag in between overlap of liner, to heat the outer overlap.

- “Break-in period” Try skiing a couple of times first and then make adjustments to the fit as needed.

Check out our fit videos on You Tube – to find them, enter:

Intuition Home

Fit Intuition Shop Fit

Intuition Spandy Andy

For more information visit: www.intuitionliners.com

Questions?  Concerns?  Email us at This email address is being protected from spambots. You need JavaScript enabled to view it. or call (604) 879-9231.

 

OR WITH OVEN

 

INSTRUCTIONS FOR FORMING GOODE THERO-FITTM LINERS

Notice: The GOODE Thermo-FitTM Liner(s) delivered to you is the correct size. It may look small, however when heated, it will easily stretch over your foot.

Background: GOODE Thermo-FitTM Liners are designed to enhance the performance and comfort of your PowerShellTM Boot System. Please follow the steps below:

1. Pre-Heat Oven to 250oF (121 oC).

2. Place liners to be molded in pre-heated over for 15 minutes.

3. Place two athletic socks over each of your feet. The socks provide additional spacing during the molding cycle.

4. Once the liners have heated for 15 minutes, wearing water ski gloves, remove one liner from the oven.

5. Slip your foot into the heated liner and pull completely over your foot. If heated properly, the liner will easily stretch over your foot. There is no designated right or left foot to the un-molded liner.

6. Quickly place your foot, with the heated liner over it, into your PowerShellTM boot. Buckle the boot so that it is just lightly snug. You DO NOT want to over tighten the buckles during the molding cycle.

7. Allow liner to cool for 5 minutes.

8. Remove foot and repeat steps 4-8 as needed.

9. Enjoy the performance and comfort of your new GOODE Thermo-FitTM Liners.

Notes: The GOODE Thermo-FitTM Liners may be reformed as needed. Just repeat all of the steps above.

 

CAUTION: DO NOT heat liners over to 250oF (121 oC). Make sure your oven has an accurate thermostat.

 

AND another oven method video.

 

_

 
Free business joomla templates